


WiseBond’s solvent-based clear high gloss floor polyurethane is 2 component 51% solids, acrylic aliphatic polyurethane designed as a non-yellowing clear coating for interior concrete, concrete overlays, or as a clear top finish coat on epoxy systems. The high-gloss clear top coat generates the premier balance of strength, added UV stability, flexibility, chemical and scratch resistance that is both user-friendly and extremely durable.
When dealing with protective coatings for concrete, which sealer you choose can vary wildly based upon the arena that the sealer is going to be applied in, the different chemicals it will be exposed to, as well as the amount of foot traffic or abrasion it will endure. In the case of choosing a sealer for an interior concrete application or overlay, there are few coatings that offer the balance of cost-efficiency and resilience as solvent polyurethane sealers. WiseBond’s Polyurethane solvent based clear topcoat has been formulated to be one of the most mechanically and chemically resistant coatings available on the market today.
The versatility as a crack treatment product allows for a relatively wide ranged in application procedures. However, the main focuses of the treatment process remain the same.
Step 1: All cracks should be "dressed" appropriately by cleaning out with a "V" blade or "crack chaser" equipped with an electric grinder.
Step 2: Make sure crack has been cleared of dust and is dry before application of SCT-EP
Step 3: Mix the Concrete Crack Filler thoroughly, until mixture is one consistent color, being careful not to mix more than you need.
Step 4: Prime the "v-joint," or cleaned out the crack, by brushing the epoxy mixture into the crack making sure it is injected into the crack.
Step 5: Combine clean, dry, inorganic silica sand with the epoxy mixture to create a thick slurry.
Step 6: Pour in the mixture and trowel it into the surface. If coming over the top with an overlay, sprinkle some sand over top of the treated crack to help create a better bond with the next coating.
Step 7: After approximately 8 hours. and the product has set, use a grinder to remove any excess materials to maintain a flat, even surface.
Coverage:Approx 300-400 square foot per gallon, per coat (varies widely based on substrate porosity and application methods)
VOC Rating: less than 435 g/L
Solids Content: 51%
Pot Life: approx 60 minutes
Shelf Life: 1 year in original unopened container
Ready for recoat: 6 - 8 hours (18+ hours at low temperatures)
Light Duty Use: 24 hours ( Up to 48 hours at low temperatures)
Heavy Traffic Ready: 3 days (Up to 5 days at low temperatues)
Full Cure: 5 - 7 days (Up to 14 days at low temperatures)
Appearance (cured): Clear Gloss
Appearance (wet): Clear
Water Resistance: Excellent, beads water
Mechanical Stability: Excellent
Light Stability: Excellent
Mechanical Properties: Direct Impact - 30 inch/pounds; Reverse Impact - 6 inch/pounds
Hardness: Pencil 4H, Konig 100
Diluent: Hydrocarbons
Odor: Solvent
Application Temperature: 50 - 90 degrees Fahrenheit
MEK: slightly softens at 3 mins, softens at 1hr, blisters at 24 hrs
Xylene: no effect at 3mins or 1hr, softens at 24 hrs
Toulene: no effect at 3 mins, slightly softens at 1hr, softens at 24 hrs
Mineral Spirits: no effect at 3mins, 1 hr or 24hrs
Ethanol: no effect at 3 mins, softens at 1 hr and 24 hrs
1,1 - Trichloroethane: no effect at 3 mins, 1 hr or 24 hrs
5% Sodium Hydroxide: no effect at 3 mins, 1 hr or 24 hrs
50% Sodium Hydroxide: no effect at 3 mins, 1 hr or 24 hrs
5% Sulfuric Acid: no effect at 3 mins, 1 hr or 24 hrs
50% Sulfuric Acid: no effect at 3 mins, 1 hr or 24 hrs
5% Hydrochloric Acid: no effect at 3 mins, 1 hr or 24 hrs
20% Hydrochloric Acid: no effect at 3 mins, 1 hr or 24 hrs
5% Nitric Acid: no effect at 3mins, 1 hr or 24 hrs
20% Nitric Acid: no effect at 3 mins and 1 hr, blisters at 24 hrs
5% Ammonia: no effect at 3 mins, 1hr or 24 hrs
Gasoline: no effect at 3 mins, 1hr or 24 hrs
Diesel Fuel: no effect at 3mins, 1hr or 24 hrs
Kerosene: no effect at 3mins, 1 hr or 24 hrs
Brake Fluid: no effect at 3 mins and 1 hr, softens/discolors at 24 hrs
Skydrol: no effect at 3 mins and 1 hr, dulls at 24 hrs
PART A - CALIFORNIA PROPOSITION 65: This product contains a chemical(s) known to the state of California to cause cancer, birth defects or reproductive harm, which are subject to the requirements of California Proposition 65. FOR MORE INFORMATION GO TO: WWW.P65WARNINGS.CA.GOV.
PART B - CALIFORNIA PROPOSITION 65: This product contains a chemical(s) known to the state of California to cause cancer, birth defects or reproductive harm, which are subject to the requirements of California Proposition 65. FOR MORE INFORMATION GO TO: WWW.P65WARNINGS.CA.GOV.
© 2023 - WiseBond®, A product of DeckWise®, The Ipe Clip® Fastener Company